BS ISO 15643:2020 pdf download – Road construction and maintenance equipment — Bituminous binder sprayers and synchronous bituminous binder sprayers-chip spreaders — Terminology and commercial specifications
This document establishes the terminology and the content of commercial literature specificationsfor bituminous binder sprayers and synchronous bituminous binder sprayers-chip spreaders (i.e.synchronised combined units]) including their components and their technical characteristics.
This document covers cold and hot bituminous binder sprayers.
2Normative references
The following documents are referred to in the text in such a way that some or all of their contentconstitutes requirements of this document. For dated references,only the edition cited applies.Forundated references, the latest edition of the referenced document(including any amendments) applies.ISO 15644,Road construction and maintenance equipment — Chippings spreaders — Terminology andcommercial specifications
3Terms and definitions
For the purposes of this document, the terms and definitions given in ISO15644 and the following apply.ISO and lEC maintain terminological databases for use in standardization at the following addresses:-ISo online browsing platform: available at https://www.iso.org/obp
一IEC Electropedia: available at http:.//www.electropedia.org/l
3.1
bituminous binder sprayer
machine used to apply a film of bituminous binder on a pavement at a predetermined application rateNote 1 to entry:The particular sprayer types may be defined by associating the operating principle, the shape ofthe components, the type of binder, and by specifying the spraying performances.
3.2
synchronised combined unit
synchronous bituminous binder sprayer-chip spreader
machine which consists of a combination of bituminous binder sprayer (3.1) and chip spreader, usedto make synchronised application of bituminous binder and chips on a pavement at predeterminedapplication rate for a complete road surface treatment
3.3
displacement pump sprayer
bituminous binder sprayer (3.1) in which bituminous binder transfer from the storage tank to the spraybar is provided by a pump
Note 1 to entry: The pump’s output is proportional to its rotating speed which may be controlled by the vehiclemovement speed.
3.14
nominal application rate
application rate at maximum output of a pumping unit(3.13) moving at a speed of 4 km/h with a binderof a density of 1 g/cm3 and a viscosity of 100 mm2/s and with maximum spray bar width (3.12)
Note 1 to entry: lt is expressed in kilograms per square metre.
3.15
binder carrying capacity
difference between the laden and kerb mass of a sprayer or synchronised combined unit (3.2)3.16
spraying height
height measured between the average plane of the pavement and the orifice of the nozzlesNote 1 to entry: lt is expressed in millimetres.
Note 2 to entry: See hz in Figure 8.
4 Description of sprayer components
4.1Transport vehicle
The vehicle, in the form of a truck, trailer or semi-trailer, carries all the components and providesmovement of the sprayer during spraying and during road transfers.
4.2Tank
The tank is used to store the binder during work and transport.
lt may have a facility to heat the binder and may have a system to prevent loss of heat, e.g. a heat-insulated sprayer.
4.3Binder transfer device
The binder transfer device provides transfer of the binder from the tank to the spray bar in order toapply a specific quantity to the pavement.
4.4Spray bar
The spray bar distributes the binder uniformly across the pavement.4.5Control station
The control station contains all the control, adjustment, measuring and automatic control equipment.There are two types, as follows.
a) Manual control: the operator adjusts all the operating parameters to obtain the required
application rate.
b) Automatic control: using predetermined operating parameters, automation ensures accuracy of
the application rate.
5 Commercial specifications of bituminous binder sprayers and spraying part of synchronised combined unit
5.1 General
The components and dimensions of a bituminous binder sprayer and spraying part of a synchronised combined unit shall be specified according to Clause 4 and 5.
The spreading part of a synchronised combined unit shall be specified according to Clause 6.
5.2 Binder sprayer components list
Examples of sprayer component lists are shown in Figures 1 a), b), c) and Figure 2 a) and b).BS ISO 15643 pdf download.